600 WN Dredging Pump->Cutting Equipment

Join

Help

shijiazhuang soarho machinary co.,ltd

	Recommended Results

600 WN Dredging Pump

Category :

Machinery on-line->Industrial Instruments & Equipment->Cutting Equipment

Product Specification

Model No:	600WN

Country	CN
Brand	Soarho
Minimum Order	1
Payment Term	L/C,T/T

Product Detail

600WN Dredging Pump


•      Product
Introduction


   600WN  is 600mm size double-shell inboard dredging pump. The safety and reliability of the double pump casing design keeps
the volute liner can be used to close to wear out, and when the liner was
broken, no water will enter the pump room.The gear box is connected with own bearing bracket.Lubrication
way is mandatory thin oil lubrication.It is single-stage, single-suction, cantilever, horizontal centrifugal pump.The flow passage of the impeller is wide through the capacity, so it is difficult
to block for pumping sand gravel or high plastic clay. It has super strong
excavation and suction ability. This  pump is simple and reliable in structure, easy to disassemble and maintain, and adoptcs high chromium wear-resistant alloy material,which has a long trouble-free life. 


600WN is marine dredging pump for dredging of river and sea.It is suitable for dredging
and filling operations of cutter-suction
dredger and trailing suction dredger. It is also used for river sand mining and
mining vessels.



 •     Product Feature


1.The structure is simple and reliable.


       600WN adopts double
pump casing structure, with its own bracket.Lubrication
way is mandatory thin oil lubrication.The safety and reliability of the double pump
casing design keeps the volute liner can be used to close to wear out, and when
the liner was broken, no water will enter the pump room.<img src="http://i.bosscdn.com/product/35/9a/8a/0f393648937b6d0c74e84b54f8.jpg" title="Double Shell Dredging Pump" alt="Double Shell Dredging Pump" />


       1  Bearing box                       2  Bearing                     3  Screw shaft sleeve           4  L-shaped seal
assembly    5  Seal box    


       6  Rear plate liner                  7  Shoulder ring             8  Volute
liner                    9  Discharge lining pipe       10  Frame plate     


     11  Gland cover plate             12  Cover
plate               13  Throat bushing             14  Water sleeves                 15  Wear ring    


     16  Impeller                                 17  Intake lining pipe             18  Seal box
protecting ring              19  Sand control plate      


     20  Impeller release collar       21  Shaft                        22    Thrust
collar              23  Impeller
release collar    24  Turning
plate


  2. Easy to assemble and disassemble and easy to
maintain. The front dismantling structure is adopted, and special disassembly
tools are equipped to facilitate disassembly and assembly.


   3.The performance of dredging is excellent. The
flow and head curve of the pump are steep, the suction ability is strong, the
ability of passing the pump is good, the change of the distance is more
applicable, and the depth of digging and the higher transportation
concentration can be reached.


   4.Good wear resistance and long life of flow
parts. The impeller, volute liner, throat bushing and rear plate liner
(wearable liner) are made of strong wear resistant alloy cast iron whose
hardness is not less than 58HRC.It has not only impact on resistance but also
high anti-abrasion performance.


   5.Using advanced hydraulic model, the pump has low
hydraulic loss, high efficiency and low energy consumption. The service life of
each part is full considered in the process of product design. The same
replacement cycle reduce the maintenance and replacement costs.


   6.The shaft seal is reliable and no leakage.


        The shaft seals adopts screw shaft sleeve
with L-shaped rubber seal device, which consists of three L-shaped seal rings
and one threaded shaft sleeve.


                <img src="http://i.bosscdn.com/product/d8/91/33/41782c29247b1b1705e5ca0d6c.jpg" width="796" height="828" title="Cutter-suction Dredger Pump" alt="Cutter-suction Dredger Pump" />


   •      Range of Performance


Capacity     Q:5000-9000m3/h


Head          H:55-73m


Discharge diameter: 600mm


   •      Outline Drawing


        See the attachment.
xhslurrypump.com

More Products from this Supplier

80ZJ High Eff. MIne Slurry Pump

4 inch Mine Slurry Pump

18/16 T-G Gravel Pump

14/12ST-AH Mining Centrifugal Slurry Pump


[ Back Products Catalog ]

Commerce Member:
Please log in your ID and password, we will later fill in relating info.

ID:

Password:

Remember my ID on this computer


	Complete this form below to send out your enquiries. All enquiries will be automatically sent to the company you want to develop.

	Subject
	Content	(Don't input Company Name, E-Mail, Phone Number, Fax Number, and URL)

Company Profile:

* Company Name

*E-mail

*Country

*Contact Person

URL

*Phone

- -

Fax

- -

*Postal code

*City

*Street Address

*Business Nature

Distributor Exporter Importer Manufacturer
Whole Sale Retailer Reseller Retrofitter User
Others, please specify:

*Security Code


Enter the security code.