Tin titanium alloy wear floor->handbag accessories

Join

Help

Jiangmen Kasole Building Materials Co., LTD.

	Recommended Results

Tin titanium alloy wear floor

Category :

Textiles and clothing->Accessories->handbag accessories

Product Specification

Country	CN
Brand	Kasole
Packing	bags
Payment Term	L/C

Product Detail

Product Overview: 
Warehouses, underground parking lots, machinery manufacturing companies and other places require that the ground cannot generate sand and dust, and can withstand the rolling of various vehicles (such as cars, forklifts, carts, etc.). Therefore, the floor of these sites must not only have general Flat protection system smooth, smooth decorative effect, but also have a strong wear resistance and compression resistance. Therefore, the corundum wear-resistant floor is a floor system that professionally solves the ground protection problems of heavy machinery manufacturing plants, industrial and commercial warehouses, underground parking lots and other ground protection issues. 
Applicable place: 
Tin titanium alloy wear floor 
1. The grounds of special places such as supermarkets, buildings, warehouses, auto showrooms, auto repair shops, and underground parking lots; 
2. The area with high mechanical performance requirements has a certain impact on the ground of the factory buildings of machinery, electronics, electrical appliances, instruments, medicine, textiles, clothing, food, and tobacco. 
3, industrial plants, production workshops, warehouses, logistics centers, garages, parking lots, supermarkets and other ground 
Product Features: 
1, impact resistance, heavy pressure, good mechanical properties; 
2, dust, mold, wear, hardness is good; 
3, resistance to heavy pressure, strong wear resistance, can not afford dust, enhance the ground oil resistance, anti-infiltration; 
4, the appearance of bright, colorful and diverse; 
5, easy to clean, easy to maintain. 
Basic requirements: 
1. The strength of grass-roots concrete should be above C25, the water-cement ratio should be controlled below 0.50, and the concrete drop should be controlled within 70-100mm. The concrete mixture should minimize segregation and control the bleeding. 
2. In order to ensure that the concrete mixture has sufficient fluidity and conducive to construction, it is recommended that concrete be added with proper additives. 
3. The concrete of the grass-roots level shall be poured and tamped with reference to the standard of the fine concrete. Note that the accurate size and the reduction of laitance production. 
4. The hardener surface is preferably constructed at the same time as the concrete structural layer. If the same leveling layer is to be applied at the same time, it is recommended that the leveling concrete should be fine stone concrete with a thickness of not less than 50mm, and consider deploying a telescopic reinforcement mesh. 
5. Pay special attention to the corners of the primary concrete construction blocks to ensure that the concrete is vibrated and compacted, and additional strengthening measures should be taken. 
Construction process: 
1.Surface treatment: using a mechanical rake equipped with a disc to evenly remove the laitance layer on the concrete surface; 
2. Distribute the material for the first time: Spread the prescribed amount of 2/3 hardened wear-resistant floor material evenly on the concrete surface of the initial setting stage, and then use a low-speed smoothing machine to perform the grinding treatment; 
3, Scratch ruler leveling: with 6 m scraping ruler, the hardened and wear-resistant material is evenly wiped horizontally and longitudinally and roughly leveled; 
4. Disperse the material for the second time: Dispense the specified amount of 1/3 colored hardened and wear-resistant material evenly (on the surface of the first abrasion-resistant material) and polish it again with a trowel. 
5. Surface polishing: According to the hardening of the concrete, adjust the angle of the blade on the polishing machine and polish the surface to ensure the smoothness and smoothness of the surface; 
6, base surface expansion: wear-resistant hardened floor within 4 to 6 hours after construction is completed, should be maintained on the surface to prevent the rapid evaporation of surface moisture to ensure the steady growth of wear-resistant material strength. 
kasole-paint.com

More Products from this Supplier

Gray epoxy anti-static topcoat

Closed epoxy base oil

Waterborne polyurethane mortar floor

Dark grey epoxy anti-static topcoat


[ Back Products Catalog ]

Commerce Member:
Please log in your ID and password, we will later fill in relating info.

ID:

Password:

Remember my ID on this computer


	Complete this form below to send out your enquiries. All enquiries will be automatically sent to the company you want to develop.

	Subject
	Content	(Don't input Company Name, E-Mail, Phone Number, Fax Number, and URL)

Company Profile:

* Company Name

*E-mail

*Country

*Contact Person

URL

*Phone

- -

Fax

- -

*Postal code

*City

*Street Address

*Business Nature

Distributor Exporter Importer Manufacturer
Whole Sale Retailer Reseller Retrofitter User
Others, please specify:

*Security Code


Enter the security code.